Most irrigation faults show up the same way: a dry patch, a sprinkler that won't pop up, a zone that won't turn on, or water where there shouldn't be any. The symptom usually points straight at the cause. Here are the problems we see most often on Melbourne systems, what causes them, and which ones you can sort out yourself.
1. A sprinkler won't pop up
Likely cause: dirt or grit jamming the riser, turf grown over the head, or low pressure on that zone.
Clear the grass and soil from around the head and run the zone. If it still sticks, the riser may need cleaning or the head replacing. If every head on the zone is struggling, it's a pressure problem, and that usually means a leak somewhere on the line.
If every sprinkler on one zone is weak but the other zones are fine, debris caught in that zone's solenoid valve is the likely cause. And if a system that worked for years suddenly can't pop up anywhere, check your water flow. Sometimes a flow restrictor gets fitted at the meter. Time how long the tap nearest your meter takes to fill a 5 or 10 litre bucket and work out litres per minute. If it's much lower than it used to be, the system needs to be split into smaller zones.
2. Dry patches in the lawn
Likely cause: a blocked or knocked nozzle, heads spaced too far apart, or a spray that's being blocked by a plant or a new piece of furniture.
Run the zone and watch where the water actually lands. Sprays should overlap, so each head throws water to the next one. A gap in the overlap shows up as a brown crescent in summer.
3. A whole zone won't turn on
Likely cause: an electrical fault between the controller and the valve, or a valve that's failed.
Check the controller first: is the zone programmed, is the controller in auto, and is a rain sensor holding it off? If the zone still won't run, the most common culprit is a wire join that wasn't sealed properly underground. Water gets in, it corrodes, and the signal stops reaching the valve. It needs tracing and re-joining.
On a service, Huw tests every station with a multimeter from the controller. A normal reading means the solenoid is fine. An open-circuit reading usually means the solenoid coil has died and needs replacing. It's a quick fix once you know which one it is.
4. A zone won't turn off
Likely cause: debris caught in the valve, holding it partly open.
Turn the zone off at the controller. If it keeps running, it's a valve problem, not a programming one. Turn off the water supply to the system until it's fixed. Clearing the debris from the valve diaphragm usually fixes it. Sometimes the diaphragm needs replacing.
5. Soggy ground, bubbling or a geyser
Likely cause: a broken pipe, a cracked fitting, or a sprinkler snapped off by a mower or car.
A broken head is obvious. A leak underground is less so: a patch that's always wet, water bubbling up around a head, low pressure on the rest of the zone, or a jump in the water bill. It needs digging up and repairing, and the sooner the better.
If water is pouring out and the controller won't stop it, turn the irrigation off at its isolation valve. Look for a black box with a green lid in the garden, a separate valve on a garden tap line, or a valve near the water meter. Know where yours is before you need it.
6. Drippers in garden beds have stopped
Likely cause: blocked emitters, a split or chewed line, or a line pulled loose from its fitting.
Run the zone and walk the bed. Check the end of each line first: if the far end is dry, there's a blockage or a break on the way. Possums, dogs and garden forks are all regular offenders.
A small break, like the dog chewing through a drip line, is often a DIY fix. Turn the zone off, cut out the damaged piece and take it to your local irrigation supply store so they can match the fittings. One thing not to do: punch extra holes in drip line to get more water. Huw has seen it more than once. Every new hole drops the flow further along the pipe, so part of the bed floods and the rest gets nothing.
7. The controller has lost its settings
Likely cause: a power outage and a flat backup battery.
Replace the backup battery, reset the time and date, and re-enter the programs. While you're there, set the run times for the season. Melbourne's permanent water use rules mean watering systems can only run between 6pm and 10am, and early morning is the best time.
When to call someone in
Clearing grass from around heads, changing a battery and adjusting a nozzle are easy jobs. Tracing a wiring fault, repairing an underground leak or rebuilding a valve takes the right gear and some experience, especially on a system with no plans.
Shaype repairs and services irrigation for homes, schools, sports grounds and owners corporations right across Melbourne, including systems we didn't install. See our irrigation repairs and servicing, or book a repair. We aim to get back to you within the next business day.
Shaype designs, installs and services irrigation across Melbourne. See our irrigation services.